Scandic Walvoil DPX100 + 2x CanBus Otto Joysticks

• 
  Neumaschine
• Type: Walvoil DPX100 + 2x CanBus Otto Joysticks
• Baujahr: 2024

Preis: auf Anfrage

Beschreibung

Hydraulic Valve Walvoil DPX 100 12/24V with 8 Proportional Sections, Open/Closed Center, and Additional Levers. The valve includes a post-compensation section. Otto Joysticks Canbus 12/24V. This kit is configured for the most popular machine settings, supporting up to 8 standard forest crane functions. If you require a different dedicated configuration, we can customize it to meet your needs, including variations in spools, voltage, the number of sections, anti-shock valves, connectors, etc. The kit is designed for plug-and-play convenience. We handle everything from the plugs to the software configuration. We provide technical support and are readily available via email, whatsup and telephone. Feel free to contact us at - or - for any inquiries or assistance. After placing an order, the flow and pressure can be fully adapted to the machine according to the customer's specific requirements. -------------------------------------------------------------------------------------------------------------------------------------------------------------- Hydraulic, sectional valve Walvoil DPX 100 with compensation, full proportional Technical specifications of default configuration: Inlet section: 32GPM 120l/min - Pmax 300 bar 4351psi Power supply port: 3/4" BPS, tank return port: 3/4" BPS 1st Main Boom 60l/min 16GPM Anti shock valves 190/80 bar 2755/1305psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever 2nd Boom 60 l/min 16GPM Anti Shock valves 190/220 bar 2755/3190psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever 3rd Slewing 40 l/min 10GPM Anti Shock valves 200/200 bar 2900/2900psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever 4th Extension 80l/min 21GPM Anti Shock valve 140 bar/plugged bar 2030psi side A 4/3 center; A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever 5th Rotator 20 l/min 5GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever 6th Grapple 60 l/min 16GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever 7th Support Left Leg 20 l/min 5GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever; Spool: 20L/min; No Anti-shock valves 8th Support Right Leg 20/min 5GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever; Spool: 60L/min; No Anti-shock valves Outlet section: with the possibility of combining valves, with bleed valve (LS relief), with pressure reducing valve. Control connection "V" and drainage connection "L" closed. Side connections "T1", "P1", "LS1" closed. DBV fixed and sealed to 175 bar at 90L/min. -------------------------------------------------------- Canbus Otto Joysticks CANBus card for analog/digital inputs. DESCRIPTION MDCi is an electronic board with CANBus interface to simulate 2 JC joysticks with 2 Otto joystick and push button dashboard. The transmission has course immediately after the turning on of the electronic card. FEATURES - supply voltage from 10 to 30 Vdc - CAN V2.0B communication bus - 120 Ohm inner terminator not present in this version - 2 diagnostic LEDs (red and green) - firmware updatable by integrated serial port SIGNALS Red LED flashing one time: short circuit error on the +5V stabilized output Red LED flashing two times: one of the analog inputs has been found not at rest position during the turning on, this input is blocked until a reset. Green LED On: the electronic card is working correctly. The green LED flashes one time every time an input (analog or on/off) change status. MDCi contro unit for OTTO joystick interface and button panel for Forest Crane Mounting version: X1 Firmware: mdc_P5_01.hex Cfg file: mdc_P5_01.cfg -------------------------------------------------------- Technical Specifications: Power Supply Voltage : 10Vdc÷30Vdc (inner 5x20 8A fuse type F8A) Current absorpion : 300mA + load outputs (max 7.5A) Wroking Temperature Range : -20 ÷+ 70 C Supply for external poterntiometers: +5V - max current 50mA PWM minimum current range : from 100 to 2500 mA PweM maximum current range: from 100 to 2500mA PWM frequency : 50-60-70-85-100-125-150-200-250-300 Hz Analog inputs impedance: 11 KOhm towards 2.5V Overlall dimensions with connector mounted: 256x210x45mm Drill interasis : 242x142mm (n. 4 holes of 6mm diameter) -------------------------------------------------------- NOTE: to have the cable L = 1.5m it is necessary to - make the joystick / cable connections 7x0.75mmq by removing the original connector - put the corrugated sheath and fix it to the bottom of the joystick (see photo) - connect the 7x0.75 cable to the Deutsch 6-pin female connector to male contacts

Kontaktdaten:

Perfekt-Trans Kamil Rutkowski
Kwietniki 14B
59-411 - Paszowice
Tel.: +48 785 845 992
Mobil: +49 162 4861903
http://www.hydraulic-master.de/